Please wait...

Categories

Presses offers 78

5
Pressure capacity: 40 t Table clamping area: 650 x 550 mm Installation height: 440 mm Column passage: 650 mm Column passage at the side: 200 mm Ram area: 580 x 250 mm Tappet bore: ø 50 mm Spindle diameter: 95 mm Ram stroke: 345 mm Table height above floor: 690 mm Number of columns: 4 Machine weight approx.: 2.1 t Machine dimensions L x W x H: 1.75 x 1.75 x 2.17 m
Pressure capacity: 40 t
Table clamping area: 650 x 550 mm
Installation height: 440 mm
Column passage: 650 mm
Column passage at the side: 200 mm
Ram area: 580 x 250 mm
Tappet bore: ø 50 mm
Spindle diameter: 95 mm
Ram stroke: 345 mm
Table height above floor: 690 mm
Number of columns: 4
Machine weight approx.: 2.1 t
Machine dimensions L x W x H: 1.75 x 1.75 x 2.17 m
Pressure: 63 t Number of strokes: 500 strokes/min Sheet width: * mm Total power requirement: 15 kW Machine weight approx.: 9 t Space requirement approx.: * m
Pressure: 63 t
Number of strokes: 500 strokes/min
Sheet width: * mm
Total power requirement: 15 kW
Machine weight approx.: 9 t
Space requirement approx.: * m
6
Pressure: 60 tons Number of strokes: 100-550 strokes/min Sheet width: 120 mm Table size: 920 x 610 mm Brother precision double roller feed: Sankyo V 60A Drive power - hoist: 22 kW Infeed width: 60 mm Column spacing (left-right): 935 mm Column spacing (front to back): 340 mm cycle time: min. Total power requirement: 32 kW Machine weight approx.: 8.5 t Space requirement approx.: 2.9 x 2.3 x 2.1 m Additional description: 4-column high-speed automatic stamping machine with hydraulic vari-drive, SANKYO V60A precision double-roller feed on the left, 3 operating modes (single stroke, continuous operation, setup), electric two-hand operation, stroke counter, blow-out device
Pressure: 60 tons
Number of strokes: 100-550 strokes/min
Sheet width: 120 mm
Table size: 920 x 610 mm
Brother precision double roller feed: Sankyo V 60A
Drive power - hoist: 22 kW
Infeed width: 60 mm
Column spacing (left-right): 935 mm
Column spacing (front to back): 340 mm
cycle time: min.
Total power requirement: 32 kW
Machine weight approx.: 8.5 t
Space requirement approx.: 2.9 x 2.3 x 2.1 m
Additional description:
4-column high-speed automatic stamping machine with hydraulic vari-drive, SANKYO V60A precision double-roller feed on the left, 3 operating modes (single stroke, continuous operation, setup), electric two-hand operation, stroke counter, blow-out device
2
Pressure: 63 t Number of strokes: 400 strokes/min Sheet width: 180 mm Stroke: 10 - 80mm Feed length: 150 mm Band Width: 180mm Control: KAISER Voltage: 380V Approx. space requirement: 1.85 x 2.70 x 3.00 m Additional description: + original Kaiser tong feed model ZR 18 D
Pressure: 63 t
Number of strokes: 400 strokes/min
Sheet width: 180 mm
Stroke: 10 - 80mm
Feed length: 150 mm
Band Width: 180mm
Control: KAISER
Voltage: 380V
Approx. space requirement: 1.85 x 2.70 x 3.00 m
Additional description:
+ original Kaiser tong feed model ZR 18 D
5
Pressure: 30 t Number of strokes: 100-600 strokes/min Sheet width: 115 mm Table size: 450x450 mm Brother precision double roller feed: BBV 190/85 left Stroke adjustable from - to: 16-40 mm Column spacing (left-right): 330 mm Column spacing (front to back): 280 mm Installation height: 290 mm Infeed width: 120 mm Feed length: 15-80mm Dimensions control cabinet: 1.1 x 1.2 x 2.2 mm Drop-through opening in the table: 315 x 100 mm Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: m Additional description: High-speed stamping machine in 3-column design, with BRUDERER BBV 190-85 feed on the left, cooling fan, swiveling protective grille, pneumatic clutch, electric 2-hand operation, manual roller ventilation in the feed
Pressure: 30 t
Number of strokes: 100-600 strokes/min
Sheet width: 115 mm
Table size: 450x450 mm
Brother precision double roller feed: BBV 190/85 left
Stroke adjustable from - to: 16-40 mm
Column spacing (left-right): 330 mm
Column spacing (front to back): 280 mm
Installation height: 290 mm
Infeed width: 120 mm
Feed length: 15-80mm
Dimensions control cabinet: 1.1 x 1.2 x 2.2 mm
Drop-through opening in the table: 315 x 100 mm
Total power requirement: 5.5 kW
Machine weight approx.: 3 t
Space requirement approx.: m
Additional description:
High-speed stamping machine in 3-column design, with BRUDERER BBV 190-85 feed on the left, cooling fan, swiveling protective grille, pneumatic clutch, electric 2-hand operation, manual roller ventilation in the feed
5
Space requirement approx.: 2.6 x 1.0 x 2.2 m Pressure: 40 tons Sheet width: 150 mm Stroke: 8 - 70mm Number of strokes - stepless: 60 - 300 min-1 Ram area: 340 x 320 mm Ram adjustment: 70 mm Table size: 550 x 580 mm Working width max.: 210 mm Lateral stand passage: 250 mm Drop-through opening in the table: 400 x 90 mm Clamping plate thickness: 60 mm Tool holder bore: Ø 40 x 80 mm Groove width: 30 mm Groove depth: 6 mm Distance between stands: 560 mm Machine weight approx.: 3.8 t Total power requirement: 7.5 kW Additional description: with original SCHAAL roller feed SWV 1E (BJ 92), infinitely variable speed adjustment, piece counter with preselection device, separate control cabinet, Unidor APS Mini control, safety emergency stop, selector switch for setup, single stroke and continuous operation, adjustment stroke
Space requirement approx.: 2.6 x 1.0 x 2.2 m
Pressure: 40 tons
Sheet width: 150 mm
Stroke: 8 - 70mm
Number of strokes - stepless: 60 - 300 min-1
Ram area: 340 x 320 mm
Ram adjustment: 70 mm
Table size: 550 x 580 mm
Working width max.: 210 mm
Lateral stand passage: 250 mm
Drop-through opening in the table: 400 x 90 mm
Clamping plate thickness: 60 mm
Tool holder bore: Ø 40 x 80 mm
Groove width: 30 mm
Groove depth: 6 mm
Distance between stands: 560 mm
Machine weight approx.: 3.8 t
Total power requirement: 7.5 kW
Additional description:
with original SCHAAL roller feed SWV 1E (BJ 92), infinitely variable speed adjustment, piece counter with preselection device, separate control cabinet, Unidor APS Mini control, safety emergency stop, selector switch for setup, single stroke and continuous operation, adjustment stroke
Pressure: 30 t Number of strokes: 100 - 600 strokes/min Stroke adjustable from - to: 8 - 40 mm Plunger adjustment: 40 mm Infeed width: 198 mm Mold installation height - min./max.: 230 - 270 mm Roller width: 110 mm Drop-through opening in the table: 310 x 80 mm Column spacing (left-right): 330 mm Column spacing (front to back): 280 mm Table height above floor: 990 mm Column diameter: 50 mm Voltage: 380V Frequency: 50/60Hz Control Voltage: 24V Table size: 475 x 450 mm Plunger diameter: 190 mm Total power requirement: 0.96 - 5.5 kW Machine weight approx.: 2.5 t Space requirement approx.: 1.2 x 1.16 x 2.15 m Additional description: Precision high-speed stamping machine in 3-column design, with: - On request, can be equipped with original Bruderer precision double roller feed, pulling and pushing on the right and left (see photo), - Electro-hydraulic VARI drive, - Pneumatic clutch with safety valve, - Three operating modes: Single stroke, single cycle and continuous operation, - central lubrication, - cooling fan for a constant machine temperature, - manometer for air pressure monitoring, - stroke counter integrated in the control panel, - separate, lockable control cabinet, - 2-hand operation and - safety emergency stop. Newly painted, optically good condition!
Pressure: 30 t
Number of strokes: 100 - 600 strokes/min
Stroke adjustable from - to: 8 - 40 mm
Plunger adjustment: 40 mm
Infeed width: 198 mm
Mold installation height - min./max.: 230 - 270 mm
Roller width: 110 mm
Drop-through opening in the table: 310 x 80 mm
Column spacing (left-right): 330 mm
Column spacing (front to back): 280 mm
Table height above floor: 990 mm
Column diameter: 50 mm
Voltage: 380V
Frequency: 50/60Hz
Control Voltage: 24V
Table size: 475 x 450 mm
Plunger diameter: 190 mm
Total power requirement: 0.96 - 5.5 kW
Machine weight approx.: 2.5 t
Space requirement approx.: 1.2 x 1.16 x 2.15 m
Additional description:
Precision high-speed stamping machine in 3-column design, with: - On request, can be equipped with original Bruderer precision double roller feed, pulling and pushing on the right and left (see photo), - Electro-hydraulic VARI drive, - Pneumatic clutch with safety valve, - Three operating modes: Single stroke, single cycle and continuous operation, - central lubrication, - cooling fan for a constant machine temperature, - manometer for air pressure monitoring, - stroke counter integrated in the control panel, - separate, lockable control cabinet, - 2-hand operation and - safety emergency stop. Newly painted, optically good condition!
3
Pressure: 30 t Number of strokes: 100-600 strokes/min Sheet width: 120 mm Table size: 450x450 mm Stroke adjustable from - to: 16-40 mm Column spacing (left-right): 330 mm Column spacing (front to back): 280 mm Installation height: 270 mm Infeed width: 120 mm Feed length: 20-100mm Drainage hole in the table: diam. 100mm Total power requirement: 5.5 kW Machine weight approx.: 2.3 +0.2 control cabinet t Additional description: ~ 6 months guarantee ~ Precision high-speed automatic stamping machine in 3-column design, machine technically, mechanically and optically overhauled, no difference to a new machine, with BRUDERER precision double-roller feed on the left, separate control cabinet, safety emergency stop
Pressure: 30 t
Number of strokes: 100-600 strokes/min
Sheet width: 120 mm
Table size: 450x450 mm
Stroke adjustable from - to: 16-40 mm
Column spacing (left-right): 330 mm
Column spacing (front to back): 280 mm
Installation height: 270 mm
Infeed width: 120 mm
Feed length: 20-100mm
Drainage hole in the table: diam. 100mm
Total power requirement: 5.5 kW
Machine weight approx.: 2.3 +0.2 control cabinet t
Additional description:
~ 6 months guarantee ~ Precision high-speed automatic stamping machine in 3-column design, machine technically, mechanically and optically overhauled, no difference to a new machine, with BRUDERER precision double-roller feed on the left, separate control cabinet, safety emergency stop
6
Pressure: 30 t Number of strokes: 100-600 strokes/min Sheet width: 198 mm Table size: 545 x 470 mm Feed:: Left Feed length: 20 - 100 mm Roller width: 110 mm Stroke adjustable from - to: 16-40 mm Column spacing (left-right): 330 mm Column spacing (front to back): 300 mm Installation height: 245 mm Ram adjustment: +/- 20 mm Plunger dimensions: ø250 x 24 mm Drop-through opening in the table: 350 x 110 mm Tappet Bore: 120mm Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: 1.0 x 1.1 x 2.1 m Additional description: Precision high-speed stamping machine in 3-column design, with: - Can be equipped with original Bruderer precision feed left or right for pulling or pushing application, - Electro-hydraulic VARI drive, - Pneumatic clutch with safety valve, - Central lubrication, - Pressure gauge for compressed air monitoring, - Cooling fan for a constant machine temperature, - main safety switch and - swiveling protective grille with safety switch.
Pressure: 30 t
Number of strokes: 100-600 strokes/min
Sheet width: 198 mm
Table size: 545 x 470 mm
Feed:: Left
Feed length: 20 - 100 mm
Roller width: 110 mm
Stroke adjustable from - to: 16-40 mm
Column spacing (left-right): 330 mm
Column spacing (front to back): 300 mm
Installation height: 245 mm
Ram adjustment: +/- 20 mm
Plunger dimensions: ø250 x 24 mm
Drop-through opening in the table: 350 x 110 mm
Tappet Bore: 120mm
Total power requirement: 5.5 kW
Machine weight approx.: 3 t
Space requirement approx.: 1.0 x 1.1 x 2.1 m
Additional description:
Precision high-speed stamping machine in 3-column design, with: - Can be equipped with original Bruderer precision feed left or right for pulling or pushing application, - Electro-hydraulic VARI drive, - Pneumatic clutch with safety valve, - Central lubrication, - Pressure gauge for compressed air monitoring, - Cooling fan for a constant machine temperature, - main safety switch and - swiveling protective grille with safety switch.
2
Pressure: 30 t Number of strokes: 100-600 strokes/min Sheet width: 120 mm Table size: 540 x 450 mm Brother precision double roller feed: left Stroke adjustable from - to: 16-40 mm Distance between columns: 330 x 300 mm Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: 2.10 x 1.65 x 0.75 m Additional description: High-speed stamping machine in 3-column design, with air cooler, piece counter, separate control cabinet, air coupling, BRUDERER precision double roller feed on the left
Pressure: 30 t
Number of strokes: 100-600 strokes/min
Sheet width: 120 mm
Table size: 540 x 450 mm
Brother precision double roller feed: left
Stroke adjustable from - to: 16-40 mm
Distance between columns: 330 x 300 mm
Total power requirement: 5.5 kW
Machine weight approx.: 3 t
Space requirement approx.: 2.10 x 1.65 x 0.75 m
Additional description:
High-speed stamping machine in 3-column design, with air cooler, piece counter, separate control cabinet, air coupling, BRUDERER precision double roller feed on the left
3
Pressure: 100 tons Number of strokes: 0 - 120 strokes/min Table surface: 1060 x 540 mm Drop-through opening in the table: 500 x 120 mm Ram area: 600 x 260 mm Ram holes x depth: 60 x 100 mm Total power requirement: 11 kW Machine weight approx.: 10 t Space requirement approx.: 2.2 x 2.3 x 2.7 m Additional description: - Automatic punching machine with protective grille that opens mechanically - Emergency stop - Analog lifting speed display - Hydraulic clutch - Separate control cabinet - UVV
Pressure: 100 tons
Number of strokes: 0 - 120 strokes/min
Table surface: 1060 x 540 mm
Drop-through opening in the table: 500 x 120 mm
Ram area: 600 x 260 mm
Ram holes x depth: 60 x 100 mm
Total power requirement: 11 kW
Machine weight approx.: 10 t
Space requirement approx.: 2.2 x 2.3 x 2.7 m
Additional description:
- Automatic punching machine with protective grille that opens mechanically - Emergency stop - Analog lifting speed display - Hydraulic clutch - Separate control cabinet - UVV
3
Pressure: 32 t Number of strokes: 30 - 1100 strokes/min Sheet width: 0 - 120 mm Table size: 760 x 580 mm Feed:: SANKYO V76 Stroke adjustable from - to: 3-50 mm Column spacing (left-right): 800 mm Column spacing (front-back): 200 Installation height: 235 mm Feed length: 0 - 76.2 mm Drop-through opening in the table: 670 x 110 mm Ram adjustment: 50 mm Ram clamping surface: 710 x 410 mm Sheet thickness: 0 - 3 mm Belt speed: max. 70 m/min Control: OP 15 SIEMENS PLC Feed angle: 165° Total power requirement: 18 kW Machine weight approx.: 6.5 t Space requirement approx.: 2.6 x 1.7 x 2.6 m Additional description: Precision high-speed stamping machine in 4-column design, precision cam feed Sankyo V 76, feed direction from right to left, with Siemens CNC control OP 15, soundproof cabin, Herion press safety valve, central lubrication, safety emergency stop
Pressure: 32 t
Number of strokes: 30 - 1100 strokes/min
Sheet width: 0 - 120 mm
Table size: 760 x 580 mm
Feed:: SANKYO V76
Stroke adjustable from - to: 3-50 mm
Column spacing (left-right): 800 mm
Column spacing (front-back): 200
Installation height: 235 mm
Feed length: 0 - 76.2 mm
Drop-through opening in the table: 670 x 110 mm
Ram adjustment: 50 mm
Ram clamping surface: 710 x 410 mm
Sheet thickness: 0 - 3 mm
Belt speed: max. 70 m/min
Control: OP 15 SIEMENS PLC
Feed angle: 165°
Total power requirement: 18 kW
Machine weight approx.: 6.5 t
Space requirement approx.: 2.6 x 1.7 x 2.6 m
Additional description:
Precision high-speed stamping machine in 4-column design, precision cam feed Sankyo V 76, feed direction from right to left, with Siemens CNC control OP 15, soundproof cabin, Herion press safety valve, central lubrication, safety emergency stop
5
Pressure: 30 t Number of strokes: 135 - 800 strokes/min Sheet width: 198 mm Table size: 540 x 460 mm Stroke adjustable from - to: 12 - 40 mm Column spacing (left-right): 330 mm Column spacing (front to back): 280 mm Installation height: 270 mm Ram adjustment: +/- 20 mm Plunger dimensions: ø250 x 25 mm Feed:: Left Feed length: 12 - 60 mm Drop-through opening in the table: 330 x 80 mm Roller width: 115 mm Machine weight approx.: 3 t Space requirement approx.: 1.1 x 1.2 x 2.1 m Additional description: High-speed stamping machine in 3-column design, with: - Mechanical 120mm roller feed, mountable on the left or right, for a pushing or pulling application, - Air friction clutch, - Central lubrication, - Power take-off via chain, on the right from the crankshaft, - Pneumatic clutch, - Swivel protective grille with safety switch and pressure gauge for compressed air monitoring.
Pressure: 30 t
Number of strokes: 135 - 800 strokes/min
Sheet width: 198 mm
Table size: 540 x 460 mm
Stroke adjustable from - to: 12 - 40 mm
Column spacing (left-right): 330 mm
Column spacing (front to back): 280 mm
Installation height: 270 mm
Ram adjustment: +/- 20 mm
Plunger dimensions: ø250 x 25 mm
Feed:: Left
Feed length: 12 - 60 mm
Drop-through opening in the table: 330 x 80 mm
Roller width: 115 mm
Machine weight approx.: 3 t
Space requirement approx.: 1.1 x 1.2 x 2.1 m
Additional description:
High-speed stamping machine in 3-column design, with: - Mechanical 120mm roller feed, mountable on the left or right, for a pushing or pulling application, - Air friction clutch, - Central lubrication, - Power take-off via chain, on the right from the crankshaft, - Pneumatic clutch, - Swivel protective grille with safety switch and pressure gauge for compressed air monitoring.
6
Pressure: 30 t Number of strokes: 100-600 strokes/min Sheet width: 120 mm Table size: 480 x 450 mm Brother precision double roller feed: left Stroke adjustable from - to: 16-40 mm Distance between columns: 330 x 300 mm Total power requirement: kW Machine weight approx.: t Space requirement approx.: 2.10 x 1.65 x 0.75 m Additional description: High-speed stamping machine in 3-column design, air clutch, BRUDERER precision double roller feed on the left
Pressure: 30 t
Number of strokes: 100-600 strokes/min
Sheet width: 120 mm
Table size: 480 x 450 mm
Brother precision double roller feed: left
Stroke adjustable from - to: 16-40 mm
Distance between columns: 330 x 300 mm
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: 2.10 x 1.65 x 0.75 m
Additional description:
High-speed stamping machine in 3-column design, air clutch, BRUDERER precision double roller feed on the left
2
Pressure: 110 tons Number of strokes: approx. 100-850 strokes/min Sheet width: approx. 10-200 mm Stroke adjustable from - to: approx. 16-75 mm Bruderer precision double roller feed: model BBV Feed length: about 2.5-120mm Table size: about 150x1070 mm Ram area: mm Plunger adjustment: approx. 89 mm Distance table - UK ram: mm Installation height: approx. 357-386 mm Total power requirement: approx. 65 kVA Machine weight approx.: approx. 28 t Approx. space requirement: approx. 3.32x2.25x3.93 m Additional description: Precision high-speed automatic stamping machine, with electro-hydraulic VARI drive, pneumatic safety clutch, electric two-hand operation, free-standing control panel with original BRUDERER speed display, piece counter with piece number preselection and automatic switch-off, motorized ram adjustment, operating mode selector switch for single stroke, set-up and single stroke , connection points for tool protection optionally also available according to your wishes, BRUDERER precision double roller feed BBV left with switchable roller ventilation, with central precision drive via main eccentric shaft, special machine feet with specially designed vibration absorption feet and special BRUDERER damping system, separate oil cooler for controlled monitoring of the temperature parameters, with belt end monitoring
Pressure: 110 tons
Number of strokes: approx. 100-850 strokes/min
Sheet width: approx. 10-200 mm
Stroke adjustable from - to: approx. 16-75 mm
Bruderer precision double roller feed: model BBV
Feed length: about 2.5-120mm
Table size: about 150x1070 mm
Ram area: mm
Plunger adjustment: approx. 89 mm
Distance table - UK ram: mm
Installation height: approx. 357-386 mm
Total power requirement: approx. 65 kVA
Machine weight approx.: approx. 28 t
Approx. space requirement: approx. 3.32x2.25x3.93 m
Additional description:
Precision high-speed automatic stamping machine, with electro-hydraulic VARI drive, pneumatic safety clutch, electric two-hand operation, free-standing control panel with original BRUDERER speed display, piece counter with piece number preselection and automatic switch-off, motorized ram adjustment, operating mode selector switch for single stroke, set-up and single stroke , connection points for tool protection optionally also available according to your wishes, BRUDERER precision double roller feed BBV left with switchable roller ventilation, with central precision drive via main eccentric shaft, special machine feet with specially designed vibration absorption feet and special BRUDERER damping system, separate oil cooler for controlled monitoring of the temperature parameters, with belt end monitoring
2
Pressure: 4 t Number of strokes: 120 - 600 strokes/min Sheet width: mm Stroke: 16mm Projection: 130 mm Drop-through opening in the table: 105 x 60 (WxD) mm Drive power: 1.1 kW Table:: 380 x 240 (WxD) mm Minimum installation height: 195 mm Plunger diameter: 90 mm Flywheel diameter: 280mm Connection voltage: 380 V Total power requirement: 1.1 kW Machine weight approx.: 0.885 t Space requirement approx.: 0.8 x 0.8 x 1.45 m Additional description: Single-column automatic punching machine with soundproof housing on a metal base, lifting speed infinitely adjustable via PIV gear, electric 2-hand operation, safety emergency stop, feed adjustment via eccentric already provided, sockets already provided on the machine for 220/380 V for belt loop control, Key switch for set-up mode / automatic, swing-away front protective hood.
Pressure: 4 t
Number of strokes: 120 - 600 strokes/min
Sheet width: mm
Stroke: 16mm
Projection: 130 mm
Drop-through opening in the table: 105 x 60 (WxD) mm
Drive power: 1.1 kW
Table:: 380 x 240 (WxD) mm
Minimum installation height: 195 mm
Plunger diameter: 90 mm
Flywheel diameter: 280mm
Connection voltage: 380 V
Total power requirement: 1.1 kW
Machine weight approx.: 0.885 t
Space requirement approx.: 0.8 x 0.8 x 1.45 m
Additional description:
Single-column automatic punching machine with soundproof housing on a metal base, lifting speed infinitely adjustable via PIV gear, electric 2-hand operation, safety emergency stop, feed adjustment via eccentric already provided, sockets already provided on the machine for 220/380 V for belt loop control, Key switch for set-up mode / automatic, swing-away front protective hood.
3
Pressure: 40 tons Number of strokes: 70-1200 strokes/min Sheet width: 200 mm Table size: 660 x 550 mm Brother precision double roller feed: BBV 201/120 Stroke adjustable from - to: 13-60 mm Drive power - hoist: 15 kW Infeed width: 200 mm Ram adjustment: 60 mm Feed length: 120mm Total power requirement: 17 kW Machine weight approx.: 7 t Space requirement approx.: 1.9 x 1.35 x 2.9 m Additional description: Precision high-speed automatic stamping machine, with electro-hydraulic VARI drive, pneumatic coupling with safety valve, electric two-hand operation, free-standing control panel with original BRUDERER speed display, piece counter, motorized ram adjustment, connection box for tool protection, BRUDERER precision double roller feed BBV201/120 on the right , driven via the main eccentric shaft, special machine feet with spring damping system, separate oil cooler to keep the temperature constant in the machine, with end-of-line monitoring
Pressure: 40 tons
Number of strokes: 70-1200 strokes/min
Sheet width: 200 mm
Table size: 660 x 550 mm
Brother precision double roller feed: BBV 201/120
Stroke adjustable from - to: 13-60 mm
Drive power - hoist: 15 kW
Infeed width: 200 mm
Ram adjustment: 60 mm
Feed length: 120mm
Total power requirement: 17 kW
Machine weight approx.: 7 t
Space requirement approx.: 1.9 x 1.35 x 2.9 m
Additional description:
Precision high-speed automatic stamping machine, with electro-hydraulic VARI drive, pneumatic coupling with safety valve, electric two-hand operation, free-standing control panel with original BRUDERER speed display, piece counter, motorized ram adjustment, connection box for tool protection, BRUDERER precision double roller feed BBV201/120 on the right , driven via the main eccentric shaft, special machine feet with spring damping system, separate oil cooler to keep the temperature constant in the machine, with end-of-line monitoring
6
Pressure: 63 t Stroke: 8 - 80mm Number of strokes: 60 - 300 strokes/min Distance between stands: 720 mm Table surface: 710 x 700 mm Drop-through opening in the table: 345 x 100 mm Lateral stand passage: 320 x 200 mm Ram area: 500 x 400 mm Ram adjustment: 80 mm Projection: 350 mm Installation height: 250 / 275 mm Tape width: mm Feed length: 220 mm Table above floor: 1000 mm Total power requirement: 9.2 kW Machine weight approx.: 6.5 t Space requirement approx.: m Additional description: With gripper feed SZV 3-S designed for a strip width of 270 mm, infinitely variable speed adjustment, separate control cabinet, safety emergency stop, selector switch for setup, single stroke and continuous operation, adjustment stroke
Pressure: 63 t
Stroke: 8 - 80mm
Number of strokes: 60 - 300 strokes/min
Distance between stands: 720 mm
Table surface: 710 x 700 mm
Drop-through opening in the table: 345 x 100 mm
Lateral stand passage: 320 x 200 mm
Ram area: 500 x 400 mm
Ram adjustment: 80 mm
Projection: 350 mm
Installation height: 250 / 275 mm
Tape width: mm
Feed length: 220 mm
Table above floor: 1000 mm
Total power requirement: 9.2 kW
Machine weight approx.: 6.5 t
Space requirement approx.: m
Additional description:
With gripper feed SZV 3-S designed for a strip width of 270 mm, infinitely variable speed adjustment, separate control cabinet, safety emergency stop, selector switch for setup, single stroke and continuous operation, adjustment stroke
6
Pressure: 315 tons Number of strokes: 20-120 strokes/min Table:: 1,750 x 1,050 mm Ram adjustment: 125 mm Installation height: 500 mm Total power requirement: 30 kW Machine weight approx.: 36 t Ram Stroke: 20-120mm Tool dimensions max.: 1,640 x 900 x 500 mm Tool weight max.: 1,750 kg Shifts per minute: 4 1/min Drop-through opening in the table: 1,100 x 300 mm Dimensions: 2,420 x 2,000 x 4,000 mm (width / depth / height) lateral drop-out opening: 1,820 x 600 mm Additional description: It is a complete stamping system with feed (working width 600mm) coiler system with coil loading chair, straightening machine as well as waste disposal system. The system is fully functional and under power. On request, the system can be demonstrated fully functional under power at the site. As this is a modern, refurbished facility, you can always call us on 0172-7300563 for any queries. The system is in a high-quality condition. A few years ago it was completely technically overhauled by a specialist company and its control technology was modernized and brought up to the most expensive standard. Unidor APS-EAD plc Control ALFV Type VP-160/600NC Servo Feed Unit AGAB Presautomation Leveller (600 mm operating width) AGAB Presautomation Decoiler Jakob Light Guards KV Svängsta Automated Haul-off Parts Conveyor
Pressure: 315 tons
Number of strokes: 20-120 strokes/min
Table:: 1,750 x 1,050 mm
Ram adjustment: 125 mm
Installation height: 500 mm
Total power requirement: 30 kW
Machine weight approx.: 36 t
Ram Stroke: 20-120mm
Tool dimensions max.: 1,640 x 900 x 500 mm
Tool weight max.: 1,750 kg
Shifts per minute: 4 1/min
Drop-through opening in the table: 1,100 x 300 mm
Dimensions: 2,420 x 2,000 x 4,000 mm (width / depth / height)
lateral drop-out opening: 1,820 x 600 mm
Additional description:
It is a complete stamping system with feed (working width 600mm) coiler system with coil loading chair, straightening machine as well as waste disposal system. The system is fully functional and under power. On request, the system can be demonstrated fully functional under power at the site. As this is a modern, refurbished facility, you can always call us on 0172-7300563 for any queries. The system is in a high-quality condition. A few years ago it was completely technically overhauled by a specialist company and its control technology was modernized and brought up to the most expensive standard. Unidor APS-EAD plc Control ALFV Type VP-160/600NC Servo Feed Unit AGAB Presautomation Leveller (600 mm operating width) AGAB Presautomation Decoiler Jakob Light Guards KV Svängsta Automated Haul-off Parts Conveyor
5
Pressure: 110 tons Stroke: 16 - 75mm Number of strokes: 100 - 850 / min Distance between columns: 1170 mm Distance table/ram, large stroke above, gain. above: approx. 450 mm Table surface: 1150 x 1070 mm Drop-through opening in the table: mm Table height above floor: mm Lateral stand passage: 400 mm Ram area: 1150 x 600 mm Ram adjustment: 89 mm Material width feed: 200 mm Material thickness feed: 12 mm Feed length: 0 - 200 mm Drive power: 50.0 kW Weight: approx. 24.6 t Space requirement (WxDxH): approx. 3.35 x 2.26 x 3.95 m Additional description: How the press stands and lies, loaded onto a truck with infinitely variable drive, single-disk clutch, motor. Ram adjustment, central lubrication, control panel
Pressure: 110 tons
Stroke: 16 - 75mm
Number of strokes: 100 - 850 / min
Distance between columns: 1170 mm
Distance table/ram, large stroke above, gain. above: approx. 450 mm
Table surface: 1150 x 1070 mm
Drop-through opening in the table: mm
Table height above floor: mm
Lateral stand passage: 400 mm
Ram area: 1150 x 600 mm
Ram adjustment: 89 mm
Material width feed: 200 mm
Material thickness feed: 12 mm
Feed length: 0 - 200 mm
Drive power: 50.0 kW
Weight: approx. 24.6 t
Space requirement (WxDxH): approx. 3.35 x 2.26 x 3.95 m
Additional description:
How the press stands and lies, loaded onto a truck with infinitely variable drive, single-disk clutch, motor. Ram adjustment, central lubrication, control panel
5
Pressure: 3kN Projection: 80 mm Stroke: 220mm Table size: 150 x 110 mm Operating pressure: 10 ATÜ Operating Voltage: 220V Machine weight approx.: 30 kg Space requirement approx.: 0.5 x 0.32 x 0.66 m
Pressure: 3kN
Projection: 80 mm
Stroke: 220mm
Table size: 150 x 110 mm
Operating pressure: 10 ATÜ
Operating Voltage: 220V
Machine weight approx.: 30 kg
Space requirement approx.: 0.5 x 0.32 x 0.66 m
3
Pressure: 100 tons Stroke: 0-500mm Table surface: 800 x 650 mm Ram area: 800 x 600 mm Drop-through opening in the table: 355 mm Table height above floor: 800 mm Installation height: 1130 mm Total power requirement: kW Machine weight approx.: 5.7 t Projection: 310 mm Space requirement approx. LxWxH: 1.2 x 2.0 x 3.67 m Additional description: The installation height is specified with the stroke at the top. Machine was converted to new safety regulations: safety distance: 270mm / overrun measurement 135 m/s, overrun 44 mm.
Pressure: 100 tons
Stroke: 0-500mm
Table surface: 800 x 650 mm
Ram area: 800 x 600 mm
Drop-through opening in the table: 355 mm
Table height above floor: 800 mm
Installation height: 1130 mm
Total power requirement: kW
Machine weight approx.: 5.7 t
Projection: 310 mm
Space requirement approx. LxWxH: 1.2 x 2.0 x 3.67 m
Additional description:
The installation height is specified with the stroke at the top. Machine was converted to new safety regulations: safety distance: 270mm / overrun measurement 135 m/s, overrun 44 mm.
3
Pressure capacity: 80 kN Passage between uprights: 650 mm Installation height: mm Table size: 600 x 500 mm Stroke: 300/400mm Installation height max.: 465 mm Total power requirement: kW Machine weight approx.: t Approx. space requirement: 2.10 x 1.20 x 1.20 m
Pressure capacity: 80 kN
Passage between uprights: 650 mm
Installation height: mm
Table size: 600 x 500 mm
Stroke: 300/400mm
Installation height max.: 465 mm
Total power requirement: kW
Machine weight approx.: t
Approx. space requirement: 2.10 x 1.20 x 1.20 m
4
Pressure: 64 t Projection: 315 mm Stroke: 8-100mm Number of strokes: 140 strokes/min Table surface: 820 x 630 mm Table height above floor: 800 mm Ram stroke adjustable min. / max.: 8-100 mm Ram adjustment: 63 mm Total power requirement: 7.5 kW Machine weight approx.: 4.8 t Space requirement approx.: 1.45 x 1.70 x 3.10 m
Pressure: 64 t
Projection: 315 mm
Stroke: 8-100mm
Number of strokes: 140 strokes/min
Table surface: 820 x 630 mm
Table height above floor: 800 mm
Ram stroke adjustable min. / max.: 8-100 mm
Ram adjustment: 63 mm
Total power requirement: 7.5 kW
Machine weight approx.: 4.8 t
Space requirement approx.: 1.45 x 1.70 x 3.10 m
3
Pressure: 25 t Projection: 260 mm Stroke: 500mm Die cushion force: 10 t Die cushion stroke: 200 mm Table top size: 500 x 500 mm Total power requirement: 11 kW Machine weight approx.: 3 t Approx. space requirement: 1.40 x 1.10 x 2.80 m Additional description: very robust design, two-hand operation, analogue pressure display
Pressure: 25 t
Projection: 260 mm
Stroke: 500mm
Die cushion force: 10 t
Die cushion stroke: 200 mm
Table top size: 500 x 500 mm
Total power requirement: 11 kW
Machine weight approx.: 3 t
Approx. space requirement: 1.40 x 1.10 x 2.80 m
Additional description:
very robust design, two-hand operation, analogue pressure display
2
Pressure: 63 t Projection: mm Stroke: 500mm Return speed: 9 m/min Forward speed: 3180mm/min Table/ram distance: 630 mm Table surface: 630 x 500 mm Operating pressure: 125 kgf/cm2 Rated Current: 18A Three-phase current 1, 2, 3 phases: 380 V Total power requirement: 8 kW Machine weight approx.: 2.6 t Space requirement approx.: m Additional description: Control of VEM Karl-Marx-Stadt Bj. 1966,
Pressure: 63 t
Projection: mm
Stroke: 500mm
Return speed: 9 m/min
Forward speed: 3180mm/min
Table/ram distance: 630 mm
Table surface: 630 x 500 mm
Operating pressure: 125 kgf/cm2
Rated Current: 18A
Three-phase current 1, 2, 3 phases: 380 V
Total power requirement: 8 kW
Machine weight approx.: 2.6 t
Space requirement approx.: m
Additional description:
Control of VEM Karl-Marx-Stadt Bj. 1966,
3
Pressure: 1.8 tons Stroke: 5/12mm Ram area: 550 x 350 mm Table surface: 920 x 460 mm Table height: 925 mm Total power requirement: 0.75 kW Machine weight approx.: 0.93 t Space requirement approx.: 0.97 x 0.95 x 1.45 m Additional description: - Oil-hydraulic swing arm punching machine - manual stroke adjustment and clamping
Pressure: 1.8 tons
Stroke: 5/12mm
Ram area: 550 x 350 mm
Table surface: 920 x 460 mm
Table height: 925 mm
Total power requirement: 0.75 kW
Machine weight approx.: 0.93 t
Space requirement approx.: 0.97 x 0.95 x 1.45 m
Additional description:
- Oil-hydraulic swing arm punching machine - manual stroke adjustment and clamping
6
Pressure: 63 t Projection: 315 mm Stroke: 200mm Drive power: 15 kW Piston stroke: 200mm Installation height max.: 450 mm Table size: 710 X 630 mm Ram clamping area: 710 X 630 mm Retraction force: 1.3 t Closing speed: 210 mm/min Return speed: 210 mm/sec Total height above floor: 2500 mm Total width: 1000mm Depth: 1600mm Engine speeds:: 1500 u7MIN: Operating Voltage: 380V Control Voltage: 220V Machine weight approx.: 5 t Additional description: Electro-hydraulic press control, permanently set safety valve, which protects against overload, safety switch-on, 2-hand pushbutton and emergency stop mushroom pushbutton, infinitely adjustable stroke adjustment, infinitely variable pressure regulation, fully automatic continuous operation, mechanical, infinitely adjustable fixed stop built into the cylinder. The stop is adjusted using a handwheel with a display scale. Automatic star-delta starter for the 15kW engine.
Pressure: 63 t
Projection: 315 mm
Stroke: 200mm
Drive power: 15 kW
Piston stroke: 200mm
Installation height max.: 450 mm
Table size: 710 X 630 mm
Ram clamping area: 710 X 630 mm
Retraction force: 1.3 t
Closing speed: 210 mm/min
Return speed: 210 mm/sec
Total height above floor: 2500 mm
Total width: 1000mm
Depth: 1600mm
Engine speeds:: 1500 u7MIN:
Operating Voltage: 380V
Control Voltage: 220V
Machine weight approx.: 5 t
Additional description:
Electro-hydraulic press control, permanently set safety valve, which protects against overload, safety switch-on, 2-hand pushbutton and emergency stop mushroom pushbutton, infinitely adjustable stroke adjustment, infinitely variable pressure regulation, fully automatic continuous operation, mechanical, infinitely adjustable fixed stop built into the cylinder. The stop is adjusted using a handwheel with a display scale. Automatic star-delta starter for the 15kW engine.
6
Pressure: 100 tons Projection: 400 mm Stroke: 320mm Distance table/ram: 670 (with large stroke at the top, gain at the top) mm Table surface: 1250 x 400 mm Table height above floor: 750 mm Ram area: 1250 x 250 mm Speed from: 95 mm/sec Speed up: 75mm/sec Working speed: 3 - 10 mm/sec Oil capacity: 400 l Drive power: 20.0 kW Machine weight approx.: 15.8 t Space requirement approx.: 2.0 x 2.85 x 4.3 m
Pressure: 100 tons
Projection: 400 mm
Stroke: 320mm
Distance table/ram: 670 (with large stroke at the top, gain at the top) mm
Table surface: 1250 x 400 mm
Table height above floor: 750 mm
Ram area: 1250 x 250 mm
Speed from: 95 mm/sec
Speed up: 75mm/sec
Working speed: 3 - 10 mm/sec
Oil capacity: 400 l
Drive power: 20.0 kW
Machine weight approx.: 15.8 t
Space requirement approx.: 2.0 x 2.85 x 4.3 m
2
Pressure: 35 t Projection: 150 mm Stroke: 8 - 100mm Ram area: 350 x 200 mm Table surface: 600 x 400 mm Number of strokes: 130 strokes/min Drop-through opening in the table: 200 x 170 mm Table height above floor: 700 mm Ram adjustment: 70 mm Total power requirement: 2.2 kW Machine weight approx.: t Space requirement approx.: 1.1 x 1.6 x 2.1 m Additional description: with pneumatically operated clutch, foot switch, hydr. opening shield by PH. Black, two-hand control
Pressure: 35 t
Projection: 150 mm
Stroke: 8 - 100mm
Ram area: 350 x 200 mm
Table surface: 600 x 400 mm
Number of strokes: 130 strokes/min
Drop-through opening in the table: 200 x 170 mm
Table height above floor: 700 mm
Ram adjustment: 70 mm
Total power requirement: 2.2 kW
Machine weight approx.: t
Space requirement approx.: 1.1 x 1.6 x 2.1 m
Additional description:
with pneumatically operated clutch, foot switch, hydr. opening shield by PH. Black, two-hand control
4
Pressure: 80 tons Projection: 280 mm Stroke: 20-120mm Table width: 710 mm Table depth: 560 mm Plunger dimensions: 560x355 mm Ram adjustment: 72 mm Number of strokes: 125 strokes/min Total power requirement: 9.5 kW Machine weight approx.: 4.4 t Space requirement approx.: m Additional description: UVV (accident prevention regulation)
Pressure: 80 tons
Projection: 280 mm
Stroke: 20-120mm
Table width: 710 mm
Table depth: 560 mm
Plunger dimensions: 560x355 mm
Ram adjustment: 72 mm
Number of strokes: 125 strokes/min
Total power requirement: 9.5 kW
Machine weight approx.: 4.4 t
Space requirement approx.: m
Additional description:
UVV (accident prevention regulation)
2
Pressure: 30 t Projection: 180 mm Stroke: 80mm Number of strokes - stepless: Hub/min Total power requirement: kW Machine weight approx.: t Space requirement approx.: 2.1 x 0.9 x 1.35 m
Pressure: 30 t
Projection: 180 mm
Stroke: 80mm
Number of strokes - stepless: Hub/min
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: 2.1 x 0.9 x 1.35 m
3
Pressure: 40 tons Projection: 280 mm Ram Stroke: 8-120mm Number of strokes: 120 strokes/min Passage: 350 mm Installation height: 270 mm Table size: 710 x 565 mm Ram area: 500 x 280 mm Total power requirement: 2.2 kW Machine weight approx.: 3.2 t
Pressure: 40 tons
Projection: 280 mm
Ram Stroke: 8-120mm
Number of strokes: 120 strokes/min
Passage: 350 mm
Installation height: 270 mm
Table size: 710 x 565 mm
Ram area: 500 x 280 mm
Total power requirement: 2.2 kW
Machine weight approx.: 3.2 t
4
Pressure: 10 T Projection: 180 mm Stroke: 8-60mm Number of strokes: 180 strokes/min Table surface: 400 x 340 mm Table height above floor: 935 mm Drop-through opening in the table: 80 mm Plunger adjustment: 40 mm Ram area: 180 x 110 mm Total power requirement: 1.1 kW Machine weight approx.: 0.6 t Space requirement approx.: 1.2 x 1.5 x 2.0 m Additional description: - Two-hand and foot operation - Control cabinet
Pressure: 10 T
Projection: 180 mm
Stroke: 8-60mm
Number of strokes: 180 strokes/min
Table surface: 400 x 340 mm
Table height above floor: 935 mm
Drop-through opening in the table: 80 mm
Plunger adjustment: 40 mm
Ram area: 180 x 110 mm
Total power requirement: 1.1 kW
Machine weight approx.: 0.6 t
Space requirement approx.: 1.2 x 1.5 x 2.0 m
Additional description:
- Two-hand and foot operation - Control cabinet
4
Pressure: 63 t Projection: 250 mm Stroke: 8-100mm Table depth: 710 mm Table width: 500 mm Ram dimensions: 450x280 mm Ram adjustment: 63 mm Number of strokes: 140 strokes/min Total power requirement: 7 kW Machine weight approx.: 3.5 t Space requirement approx.: m
Pressure: 63 t
Projection: 250 mm
Stroke: 8-100mm
Table depth: 710 mm
Table width: 500 mm
Ram dimensions: 450x280 mm
Ram adjustment: 63 mm
Number of strokes: 140 strokes/min
Total power requirement: 7 kW
Machine weight approx.: 3.5 t
Space requirement approx.: m
3
Pressure: 36 t Projection: 280 mm Stroke: 6 - 82mm Plunger adjustment: 51 - 13 mm Number of strokes: 6-82 strokes/min Table surface: 530 x 480 mm Drop-through opening in clamping plate: Ø 140 mm Clamping plate thickness: 70 mm Ram area: 200 x 200 mm Clamping plate: 530 x 450 mm Total power requirement: kW Machine weight approx.: t Approx. space requirement: 1.0 x 1.65 x 1.80 m Additional description: WEINGARTEN flywheel eccentric press with UVV protection screen make DITTMER PSK 103/B Bj. 1978, additional clamping plate 530 x 450 mm (clamping plate thickness: 70 mm) manual central lubrication, height-adjustable table (+/- 180 mm)
Pressure: 36 t
Projection: 280 mm
Stroke: 6 - 82mm
Plunger adjustment: 51 - 13 mm
Number of strokes: 6-82 strokes/min
Table surface: 530 x 480 mm
Drop-through opening in clamping plate: Ø 140 mm
Clamping plate thickness: 70 mm
Ram area: 200 x 200 mm
Clamping plate: 530 x 450 mm
Total power requirement: kW
Machine weight approx.: t
Approx. space requirement: 1.0 x 1.65 x 1.80 m
Additional description:
WEINGARTEN flywheel eccentric press with UVV protection screen make DITTMER PSK 103/B Bj. 1978, additional clamping plate 530 x 450 mm (clamping plate thickness: 70 mm) manual central lubrication, height-adjustable table (+/- 180 mm)
3
Pressure: 70 tons Projection: 250 mm Stroke: 10 - 120mm Table size: 750 x 500 mm Installation height: 350 mm Ram adjustment: 350 x 200 mm Number of strokes: 50 strokes/min Passage: 310 x 370 mm Total power requirement: 5 kW Machine weight approx.: 3.5 t Space requirement approx.: 1.3 x 1.4 x 2.5 m Additional description: - inclinable single-column eccentric press - tie rod design with UVV movable protective screen - pneumatic clutch - 4-fold guided ram - separate control cabinet - central lubrication - electric two-hand release - safety emergency stop
Pressure: 70 tons
Projection: 250 mm
Stroke: 10 - 120mm
Table size: 750 x 500 mm
Installation height: 350 mm
Ram adjustment: 350 x 200 mm
Number of strokes: 50 strokes/min
Passage: 310 x 370 mm
Total power requirement: 5 kW
Machine weight approx.: 3.5 t
Space requirement approx.: 1.3 x 1.4 x 2.5 m
Additional description:
- inclinable single-column eccentric press - tie rod design with UVV movable protective screen - pneumatic clutch - 4-fold guided ram - separate control cabinet - central lubrication - electric two-hand release - safety emergency stop
4
Pressure: 75 t Projection: 320 mm Stroke: 6 - 100mm Number of strokes: 105 strokes/min Ram adjustment: 60 - 13 mm Installation height: 280 mm Sheet thickness - max.: 5.5 mm Clamping plate: 610 x 540 mm Fall-through opening in clamping plate: 150 x 150 mm Plunger area: 40 x 28 mm Clamping plate thickness: 80 mm Table:: 650 x 580 mm Total power requirement: kW Machine weight approx.: 1.2 t Approx. space requirement: 1.50 x 1.30 x 2.20 m Additional description: WEINGARTEN eccentric flywheel press, equipped with an additional clamping plate 610 x 540 mm (thickness of clamping plate 80 mm), manual central lubrication, stroke counter
Pressure: 75 t
Projection: 320 mm
Stroke: 6 - 100mm
Number of strokes: 105 strokes/min
Ram adjustment: 60 - 13 mm
Installation height: 280 mm
Sheet thickness - max.: 5.5 mm
Clamping plate: 610 x 540 mm
Fall-through opening in clamping plate: 150 x 150 mm
Plunger area: 40 x 28 mm
Clamping plate thickness: 80 mm
Table:: 650 x 580 mm
Total power requirement: kW
Machine weight approx.: 1.2 t
Approx. space requirement: 1.50 x 1.30 x 2.20 m
Additional description:
WEINGARTEN eccentric flywheel press, equipped with an additional clamping plate 610 x 540 mm (thickness of clamping plate 80 mm), manual central lubrication, stroke counter
3
Pressure: 35 t Projection: 220 mm Stroke: 4-70mm Ram adjustment: 50 mm Number of strokes: 110 strokes/min Table surface: 700 x 450 mm Drop-through opening in the table: 155 mm Total power requirement: 2.2 kW Machine weight approx.: t Space requirement approx.: 1.3 x 1.0 x 2.1 m Additional description: compact single-column eccentric press, hydraulically opening protective screen, emergency stop, foot switch
Pressure: 35 t
Projection: 220 mm
Stroke: 4-70mm
Ram adjustment: 50 mm
Number of strokes: 110 strokes/min
Table surface: 700 x 450 mm
Drop-through opening in the table: 155 mm
Total power requirement: 2.2 kW
Machine weight approx.: t
Space requirement approx.: 1.3 x 1.0 x 2.1 m
Additional description:
compact single-column eccentric press, hydraulically opening protective screen, emergency stop, foot switch
6
Pressure: 160 tons Projection: 300 mm Stroke: 30 - 120mm Table size: 1000 x 700 mm Ram adjustment: 70 mm Ram strokes: 50 strokes/min Total power requirement: kW Machine weight approx.: 12.12 t Approx. space requirement: 3.80 x 2.70 x 2.60 m Additional description: with gripper feed on the right and integrated 6-roller straightening machine for a width of up to 220 mm, pneumatic clutch, piece counter
Pressure: 160 tons
Projection: 300 mm
Stroke: 30 - 120mm
Table size: 1000 x 700 mm
Ram adjustment: 70 mm
Ram strokes: 50 strokes/min
Total power requirement: kW
Machine weight approx.: 12.12 t
Approx. space requirement: 3.80 x 2.70 x 2.60 m
Additional description:
with gripper feed on the right and integrated 6-roller straightening machine for a width of up to 220 mm, pneumatic clutch, piece counter
3
Pressure: 75 t Projection: 400 mm Stroke: 6 - 100mm Plunger adjustment: 13-60 mm Number of strokes: 60 strokes/min Installation height: 350 mm Table surface: 620x600 mm Ram area: 400x280 mm Total power requirement: 5.0 kW Machine weight approx.: 4.5 t Space requirement approx.: 0.95 x 2.52 x 2.32 m Additional description: Single-column eccentric press with electromagnetically switched and indexed turret rotary table Ø 950 mm, with 10 switching stations, turret table height 75 mm, with manual central lubrication, gear reduction, maintenance unit, electric two-hand release, safety emergency stop
Pressure: 75 t
Projection: 400 mm
Stroke: 6 - 100mm
Plunger adjustment: 13-60 mm
Number of strokes: 60 strokes/min
Installation height: 350 mm
Table surface: 620x600 mm
Ram area: 400x280 mm
Total power requirement: 5.0 kW
Machine weight approx.: 4.5 t
Space requirement approx.: 0.95 x 2.52 x 2.32 m
Additional description:
Single-column eccentric press with electromagnetically switched and indexed turret rotary table Ø 950 mm, with 10 switching stations, turret table height 75 mm, with manual central lubrication, gear reduction, maintenance unit, electric two-hand release, safety emergency stop
3
Pressure: 63 t Projection: 250 mm Stroke: 8 - 100mm Number of strokes: 120 strokes/min Table:: 715 x 500mm Installation height: 330 mm Ram adjustment: 63 mm Clamping plate: 700 x 480 mm Drop-through opening in the table: 240 mm Drop-through opening in clamping plate: 110 mm Ram clamping surface: 450 x 280 mm Total power requirement: kW Machine weight approx.: 5.5 t Space requirement approx.: 1.2 x 1.7 x 2.7 m Additional description: Single-column eccentric press in inclinable construction via hydraulic adjustment system, inclinable in 4 stages, drop-through opening to the rear (325 x 500 mm) or below (360 x 160 mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, 2-hand operation, Foot release can be set up, operating mode selector switch for setting up continuous or single stroke, emergency stop switch, piece counter, various accessories
Pressure: 63 t
Projection: 250 mm
Stroke: 8 - 100mm
Number of strokes: 120 strokes/min
Table:: 715 x 500mm
Installation height: 330 mm
Ram adjustment: 63 mm
Clamping plate: 700 x 480 mm
Drop-through opening in the table: 240 mm
Drop-through opening in clamping plate: 110 mm
Ram clamping surface: 450 x 280 mm
Total power requirement: kW
Machine weight approx.: 5.5 t
Space requirement approx.: 1.2 x 1.7 x 2.7 m
Additional description:
Single-column eccentric press in inclinable construction via hydraulic adjustment system, inclinable in 4 stages, drop-through opening to the rear (325 x 500 mm) or below (360 x 160 mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, 2-hand operation, Foot release can be set up, operating mode selector switch for setting up continuous or single stroke, emergency stop switch, piece counter, various accessories
3
Pressure: 12 t Projection: 220 mm Stroke: 6-66mm Number of strokes: 160 strokes/min Sheet thickness - max.: 2 mm Plunger adjustment: 42 -12 mm Table:: 585 x 400mm Clamping plate thickness: 60 mm Plunger area: 170 x 170 mm Drop-through opening in clamping plate: Ø 80 mm Clamping plate: 600 x 400 mm Total power requirement: kW Machine weight approx.: t Space requirement approx.: m Additional description: WEINGARTEN flywheel eccentric press, equipped with UVV protection screen Make: DITTMER Type: PSK 103/B, manual central lubrication, foot switch, additional clamping plate 600 x 400 mm (plate thickness 60 mm), table height adjustable (+/- 170 mm)
Pressure: 12 t
Projection: 220 mm
Stroke: 6-66mm
Number of strokes: 160 strokes/min
Sheet thickness - max.: 2 mm
Plunger adjustment: 42 -12 mm
Table:: 585 x 400mm
Clamping plate thickness: 60 mm
Plunger area: 170 x 170 mm
Drop-through opening in clamping plate: Ø 80 mm
Clamping plate: 600 x 400 mm
Total power requirement: kW
Machine weight approx.: t
Space requirement approx.: m
Additional description:
WEINGARTEN flywheel eccentric press, equipped with UVV protection screen Make: DITTMER Type: PSK 103/B, manual central lubrication, foot switch, additional clamping plate 600 x 400 mm (plate thickness 60 mm), table height adjustable (+/- 170 mm)
4
Pressure: 50 tons Projection: 250 mm Stroke: 8-120mm Ram area: 350 x 180 mm Table surface: (W x D) 650 x 520 mm Number of strokes: 55 strokes/min Drop-through opening in the table: 250 mm Table height above floor: 820 mm Installation height: 420 mm Stroke adjustment: 8 - 120 mm Engine speeds:: 1420 rpm Current: 8.8A Pivot hole in ram: 42 mm Table adjustment up: 200 mm Total power requirement: 2.2 kW Machine weight approx.: 1.5 t Space requirement approx.: WxDxH 80x150x 210 cm Additional description: Single-column eccentric press in a compact design with gear train and adjustable work table, foot release, stroke counter, additional clamping plate with 4 grooves, drop-through hole diameter 120 mm, groove width 21 mm, plate thickness 55 mm, main safety switch
Pressure: 50 tons
Projection: 250 mm
Stroke: 8-120mm
Ram area: 350 x 180 mm
Table surface: (W x D) 650 x 520 mm
Number of strokes: 55 strokes/min
Drop-through opening in the table: 250 mm
Table height above floor: 820 mm
Installation height: 420 mm
Stroke adjustment: 8 - 120 mm
Engine speeds:: 1420 rpm
Current: 8.8A
Pivot hole in ram: 42 mm
Table adjustment up: 200 mm
Total power requirement: 2.2 kW
Machine weight approx.: 1.5 t
Space requirement approx.: WxDxH 80x150x 210 cm
Additional description:
Single-column eccentric press in a compact design with gear train and adjustable work table, foot release, stroke counter, additional clamping plate with 4 grooves, drop-through hole diameter 120 mm, groove width 21 mm, plate thickness 55 mm, main safety switch
5
Ram retraction force: 1600 kN Die cushion: 800 kN Blank holder pressure: 800 kN Ram stroke: 700 mm Pull Stroke: 250mm Blank holder stroke: 400 mm Installation height: 1100/1400 mm Table size: 1000 x 1000 mm Table height: 750 mm Space requirement approx.: 2.3 x 1.2 x 5.3 m Additional description: - Machine comes from a university and has hardly run - only 586 operating hours!!!!! - Oil tank volume: 1300 l / HPL 46 - Press force with coupling plate 2400 kN
Ram retraction force: 1600 kN
Die cushion: 800 kN
Blank holder pressure: 800 kN
Ram stroke: 700 mm
Pull Stroke: 250mm
Blank holder stroke: 400 mm
Installation height: 1100/1400 mm
Table size: 1000 x 1000 mm
Table height: 750 mm
Space requirement approx.: 2.3 x 1.2 x 5.3 m
Additional description:
- Machine comes from a university and has hardly run - only 586 operating hours!!!!! - Oil tank volume: 1300 l / HPL 46 - Press force with coupling plate 2400 kN
8
Pressure: 150 tons Bending length: 3100 mm Distance between columns: 2700 mm Total power requirement: 15.0 kW Machine weight approx.: 10 t Approx. space requirement: 3.115 x 1.66 x 2.785 m Projection: 400 mm Stroke: 150mm Installation height: 450 mm
Pressure: 150 tons
Bending length: 3100 mm
Distance between columns: 2700 mm
Total power requirement: 15.0 kW
Machine weight approx.: 10 t
Approx. space requirement: 3.115 x 1.66 x 2.785 m
Projection: 400 mm
Stroke: 150mm
Installation height: 450 mm
3
Pressure: 80 tons Bending length: 2505 mm Distance between columns: 2200 mm Total power requirement: 7.3 kVA Machine weight approx.: 5.6 t Approx. space requirement: 3 x 2.25 x 2.20 m Additional description: - Control AMADA-MELDAS NC 9 F over 7 axes - detailed documents for the machine are available - good condition
Pressure: 80 tons
Bending length: 2505 mm
Distance between columns: 2200 mm
Total power requirement: 7.3 kVA
Machine weight approx.: 5.6 t
Approx. space requirement: 3 x 2.25 x 2.20 m
Additional description:
- Control AMADA-MELDAS NC 9 F over 7 axes - detailed documents for the machine are available - good condition
6
Pressure: 80 tons Bending length: 2550 mm Distance between columns: 2050 mm Installation height: max. 520 mm Ram stroke - max.: 160 mm Stand projection: 300 mm Lifting speed - down empty: 100 mm/sec Lifting speed - under load: 11 mm/sec Lifting speed - return: 100 mm/sec Total power requirement: 14 kW Machine weight approx.: 6.6 t Space requirement approx.: 3.0 x 1.9 x 2.7 m
Pressure: 80 tons
Bending length: 2550 mm
Distance between columns: 2050 mm
Installation height: max. 520 mm
Ram stroke - max.: 160 mm
Stand projection: 300 mm
Lifting speed - down empty: 100 mm/sec
Lifting speed - under load: 11 mm/sec
Lifting speed - return: 100 mm/sec
Total power requirement: 14 kW
Machine weight approx.: 6.6 t
Space requirement approx.: 3.0 x 1.9 x 2.7 m
7
Print: . t Table length: . mm Table width: . mm Total power requirement: . kW Machine weight approx.: 22 t Space requirement approx.: . m
Print: . t
Table length: . mm
Table width: . mm
Total power requirement: . kW
Machine weight approx.: 22 t
Space requirement approx.: . m
10
Pressure: 650 tons Passage width: 920 mm Stroke: 1750mm Table surface: 2000x1500 mm Ram area: 2000x1500 mm Installation height: 2100 mm Hydraulics: 203 bar Closing speed: 500 mm/sec Press Speed: 0.5-10.4mm/sec Hole in Plunger Diameter/Depth: mm Opening Speed: 250mm/250 Retraction force: 150 tons Total power requirement: 75 kW Machine weight approx.: 47 t Space requirement approx.: 4.4x2.5x7.5 m
Pressure: 650 tons
Passage width: 920 mm
Stroke: 1750mm
Table surface: 2000x1500 mm
Ram area: 2000x1500 mm
Installation height: 2100 mm
Hydraulics: 203 bar
Closing speed: 500 mm/sec
Press Speed: 0.5-10.4mm/sec
Hole in Plunger Diameter/Depth: mm
Opening Speed: 250mm/250
Retraction force: 150 tons
Total power requirement: 75 kW
Machine weight approx.: 47 t
Space requirement approx.: 4.4x2.5x7.5 m